WHITE-KAR MODELS (Slot Car Kits)
NY MODIFIEDS 3D PRINTED MODIFIED SLOT CARS AND ACCESORIES.
"WHITE-KAR-MODELS" 3D printed slot cars – Bodies – Chassis – Wheels/Inserts – Drivers – Accesories
The future has been here for a few years now, and it is time to get involved with 21st Century technology...
We drew up an accurate 3D model of a '35 Chevy Vintage Modified Coupe that ran Islip Speedway back in late 60s, early 70s. In addition to this '35 Coupe there are many other modifieds in the works as well!
The Islip Speedway Jarzombeck Offset Coupe working box art alongside a quick render; a 3D printed Vintage Modified Coupe available soon from "White-Kar Models" in 1/32! It's almost ready!
3D printing technology is moving quickly. That said, the surface finish and detail on our test car is better than expected. Ideally we would want to replicate iconic asphalt Modifieds from the Golden Era (1968-74?) that raced on Long Island, and in New York state, and of course, New England. In addition to full car kits, we have a few pieces and parts that should be of help for builders as well.
Below are some resin model car parts.
• RESIN MODEL CAR AND SLOT CAR PARTS.
Driver figure with containment seat:
Driver figure bust with Containment seat
for NY Modifieds Laminate Tour Mods
(click to enlarge) |
Driver – with Containment seat ........ $3.00
This driver figure bust is sized for the NY Tour Modified Laminate Modifieds, which have a 4" wheelbase. They will also fit Reality Modified and Jer's Modified bodies. So it is slightly smaller than 1/25 in size...
This driver figure has a contemporary containment safety seat as found on current Nascar Modifieds. This should replace the old Champion bust with a much higher level of detail.
Package comes with an adhesive transfer mounting sheet to locate and affix the driver to the interior card.
|
Driver figure, vintage modified:
Driver bust Vintage (click to enlarge)
|
Driver – Vintage .......... $3.00
This driver figure bust is sized for 1/24 and 1/25 scale builds.
This driver figure has vintage type open-face helmet, and older seat, headrest and steering wheel styles.
Package comes with an adhesive transfer mounting sheet to locate and affix the driver to the interior card.
|
Driver figure, full helmet:
Driver bust with full helmet (click to enlarge)
|
Driver – Full-helmet ......... $3.00
This driver figure bust is sized for 1/24 and 1/25 scale builds.
This driver figure has a full-face helmet.
Package comes with an adhesive transfer mounting sheet to locate and affix the driver to the interior card.
|
Driver figure, with 'goggles':
Driver bust with 'goggles' (click to enlarge)
|
Driver – with 'Goggles'......... $3.00
This driver figure bust is sized for 1/24 and 1/25 scale builds.
This driver figure has an open-face helmet, and protective goggles.
Package comes with an adhesive transfer mounting sheet to locate and affix the driver to the interior card.
|
'Wide-5' wheel inserts for CB Design rims:
Modified 'Wide-5' Style Wheel Inserts.
(click to enlarge)
|
Wide-5 inserts CB Design 15x12 rim (set of four)...... $6.00
These inserts are sized to fit the CB Design 15x12 insert wheel used primarily for 1/32 scale cars.
The 'Wide-5' wheel is the setup used by the actual 1:1 Modifieds. Use the four-bolt hubs up front and the eight-bolt hubs for the rear.
If you click/enlarge the photo of the raw unpainted wheel you can see fine detail, hexagonal wheel lug nuts, cylindrical studs, and air valve stems.
|
Wide-5 inserts for Pro-Track 1/2" hub:
Wide-5 inserts for '27mm' Pro-Track and H&R 5/8" hub:
Modified 'Wide-5' Style Wheel Inserts.
(sized to fit the 27mm Pro-Track wheel/tire) |
Wide-5 inserts for Pro-Track 5/8" hub (set of four)...... $6.00
These inserts are sized to fit the BIG Pro-Track 5/8" hub as found on the 27mm Pro-Track and 27mm H&R wheel/tires - Very popular with slot car racers who want a *scale appearance* for their hard body Modified builds.
These are also used by static modelers - the 5/8" hub insert is an important size not often covered for slot car racing.
|
These inserts are sized and designed for a press fit in the rim. If need be, the inserts can be glued in place, or shimmed, as needed.
Here is a link to some resin printed projects and White-Kar Models stuff on Home Racing World (a great oval track slot racing forum) - Check it out !
I accept paypal and if you email me at nymodifieds@gmail.com I will get back to you regarding cost, shipping, and turnaround.
Let me know whatever you need or if you have any questions.
nymodifieds@gmail.com
---
